In short: an audio compressor reduces the gap between the loud and quiet parts of a sound. Above a threshold, it lowers the level according to a ratio, at a speed set by attack and release. Set well, it makes a vocal steadier or drums punchier.
Not to be confused with file compression (MP3, AAC), which shrinks a file by discarding information. Here we're talking about dynamic range compression: a volume process used in mixing and mastering.
How an audio compressor works
The compressor constantly monitors the signal level. As long as it stays below the threshold, nothing happens. As soon as it goes over, the compressor turns down the part that exceeds it. The result is a steadier sound, which you can then bring back up with makeup gain.
Compressor parameters
| Parameter | What it does | Rule of thumb |
|---|---|---|
| Threshold | Level above which compression kicks in | The lower it is, the harder the compressor works |
| Ratio | How strongly the level is reduced above the threshold | 2:1 gentle, 4:1 firm, 10:1 and up = limiting |
| Attack | How fast compression starts | Slow (20–40 ms) keeps drum transients |
| Release | How fast it stops | Too short: pumping; too long: dull sound |
| Knee | Soft or hard transition around the threshold | Soft knee sounds more natural |
| Makeup gain | Brings level back up after compression | Compare at matched loudness with and without |
The gain reduction meter is your best guide: it shows how many decibels the compressor is taking off. 2 to 6 dB on a vocal and 1 to 3 dB in mastering are common ballpark figures.
Starting settings by instrument
Starting points, to adjust by ear for each song.
| Source | Ratio | Attack | Release | Gain reduction |
|---|---|---|---|---|
| Lead vocal | 3:1 to 4:1 | 5–15 ms | 50–100 ms | 3 to 6 dB |
| Kick | 4:1 | 20–30 ms | 50–80 ms | 3 to 5 dB |
| Snare | 4:1 | 10–30 ms | 60–100 ms | 3 to 6 dB |
| Bass / 808 | 3:1 to 4:1 | 10–30 ms | 80–150 ms | 3 to 6 dB |
| Drum bus | 2:1 to 4:1 | 10–30 ms | Auto or 100 ms | 2 to 4 dB |
| Mastering | 1.5:1 to 2:1 | 30 ms or more | 100–300 ms | 1 to 3 dB |
Types of compressors
- VCA: fast and precise, ideal on drums and the master bus
- Optical: smooth, gradual response, popular on vocals and bass
- FET: very fast with character, often used on vocals and drums
- Multiband: compresses several frequency ranges separately, useful in mastering in small doses
Two useful techniques
Parallel compression
Send the track to a heavily compressed bus, then blend that signal with the original. You get density and punch without losing the natural attack. Widely used on drums and sometimes on vocals.
Sidechain
The compressor reacts to another track's signal. Classic example: the bass dips slightly on every kick, freeing up the low end. The same idea makes room for the vocal.
Common mistakes
- Comparing with and without compression without matching levels: louder always seems better
- An attack so fast it flattens drum transients
- Too much gain reduction: a flat, tiring sound
- Compressing every track "just because"
- Stacking several heavy compressors instead of spreading the work gently
Master bus compression is a special case: when exporting for mastering, leave it without heavy processing. See our guide on how to mix your music and our 10 mixing and mastering mistakes.
Compression in mastering
In mastering, compression is light: it glues the mix and controls dynamic swings without changing its character. At Mastering France, compression settings are chosen by an AI from the track's measurements, with an attack of at least 25 ms to preserve transients, and limits specific to each style.



